Skip to content

Latest commit

 

History

History
187 lines (140 loc) · 5.7 KB

README.md

File metadata and controls

187 lines (140 loc) · 5.7 KB

RFID Library Build Status

125Khz RFID library for Arduino.

This library only support TTL RS232 serial port.

125Khz RFID Reader

Grove - 125KHz RFID Reader

When read the data from some RFID card, you will get data like 00 91 6f 0b f5.

Example:

your card number: 0009531147
that your data  : 00 91 6f 0b f5

Notice, f5 is the check bit

f5 = 00^91^6f^0b

Pins

  1. VCC support 3.3 ~ 5V
  2. TX, RX connect to Arduino or Seeeduino
  3. T1, T2 is the Signal port for RFID antenna
  4. W0, W1 is for wiegand protocol, but this library not support yet.
     		+-----------+
++++++++----|VCC	  T1|----
|  +++++----|GND	  T2|----
|  | |++----|TX		 SER|----
|  | |	----|RX		 LED|----	
|  | |	----|W0		BEEP|----
|  | |	----|W1		 GND|----
|  | |		+-----------+
|  | \___________________________________
|  |_____________________________        |
|                                |       |
|                              + + + + + + + +  + + + + + + + +
|                              | | | | | | | |  | | | | | | | |
|                              | | | | | | | |  | | | | | | | |
|            +-----------------|-|-|-|-|-|-|-|--|-|-|-|-|-|-|-|-+
|            |                 x-x-x-x-x-x-x-x  x-x-x-x-x-x-x-x |
|            |              xxx                                 |
|       +--------+          xxx    --- ---    .............     |
|       |        |                | - x + |  ' |  ||\ |.-. '    +
|       |        |          ^      --- ---   | |__|| \|._. |     x
|       |        |        <+++>    ARDUINO   '.............'      +
|       +--------+          V                                     |
|            |            _____                       ++-++   xx  |
|            |           <_____>                      +-O-+   xx  |
|            |                                        ++-++   xx  |
|            |+--++--                                             |
|            ||||++--                  +---------------------+    |
|            |+--++--                  |                     |    |
|            |                         |                     |    |
|         ++------+                    +---------------------+    |
|         ++      |                                               +
|         ++      |          +-+ +-+                             x
|         ++------+          +-+ +-+   x-x-x-x-x-x x-x-x-x-x-x  +
|            +-------------------------|-|-|-|-|-|-|-|-|-|-|-|--+
|                                      | | | | | | | | | | | |
|                                      | | | | | | | | | | | |
|                                      + + + + + + + + + + + +
|____________________________________________|
	

Usage

Connecting RFID Reader RX, TX to Arduino pin headers.

RX <--> 10 TX <--> 11

// RFID_UART.ino

#include <SoftwareSerial.h>
#include <SeeedRFID.h>

#define RFID_RX_PIN 10
#define RFID_TX_PIN 11

#define TEST

SeeedRFID RFID(RFID_RX_PIN, RFID_TX_PIN);
RFIDdata tag;

void setup() {
	Serial.begin(57600);
	Serial.println("Hello, double bk!");
}

void loop() { 
	if(RFID.isAvailable()){
		tag = RFID.data();
		Serial.print("RFID card number: ");
		Serial.println(RFID.cardNumber());
#ifdef TEST
	Serial.print("RFID raw data: ");
	for(int i=0; i<tag.dataLen; i++){
	    Serial.print(tag.raw[i], HEX);
	    Serial.print('\t');
		}
#endif
	}
}

Using multiple readers

When using multiple readers, you'll need to call the 'listen' function in order to receive any future readings.

// RFID_UART.ino

#include <SoftwareSerial.h>
#include <SeeedRFID.h>

#define RFID_RX_PIN 10
#define RFID_TX_PIN 11

#define RFID2_RX_PIN 12
#define RFID2_TX_PIN 13


SeeedRFID RFID(RFID_RX_PIN, RFID_TX_PIN);
RFIDdata tag;

SeeedRFID RFID2(RFID2_RX_PIN, RFID2_TX_PIN);
RFIDdata tag2;

void setup() {
  Serial.begin(9600);
  RFID.listen(); //first, we listen for data on reader #1
}

void loop() { 

  if(RFID.isAvailable()){
    tag = RFID.data();
    Serial.print("RFID card number: ");
    Serial.println(RFID.cardNumber());
    RFID2.listen(); //now start listening for data on reader #2
  }

  if(RFID2.isAvailable()){
    tag2 = RFID2.data();
    Serial.print("RFID2 card number: ");
    Serial.println(RFID2.cardNumber());
    RFID.listen(); //then we listen to reader #1 again...
  }
}

For more information please visit wiki.


This library is written by Ye Xiaobo for seeed studio
and is licensed under The MIT License.

Contributing to this software is warmly welcomed. You can do this basically by
forking, committing modifications and then pulling requests (follow the links above
for operating guide). Adding change log and your contact into file header is encouraged.
Thanks for your contribution.

Seeed Studio is an open hardware facilitation company based in Shenzhen, China.
Benefiting from local manufacture power and convenient global logistic system,
we integrate resources to serve new era of innovation. Seeed also works with
global distributors and partners to push open hardware movement.

Analytics