Skip to content

Latest commit

 

History

History
257 lines (192 loc) · 8.11 KB

README.md

File metadata and controls

257 lines (192 loc) · 8.11 KB
Raw

Operations

Proxmark3 antennas

  • lf tune: 46V
  • hf tune: 37V

Power Consumption

Consumption measured over the 5V USB-C

  • 325mA when idle and not charging the battery
  • 411mA lf tune
  • 450mA hf tune

Temperature

H3 on NanoPi NEO and LCD become quite hot...

NanoPi H3

iCopy-X LCD

Upgrade

Official way to upgrade is

  • Get the serial written on the device, e.g. 01234567
  • Email it to team@icopy-x.com or fill it in https://www.icopy-x.com/updates and get back a 01234567.ipk file.
  • Set the device into PC-Mode, connect to a PC and drop 01234567.ipk at the root
  • Go to About / Go down to next page / Update firmware

This will update the Python frontend and the proxmark3 client running on the NanoPi NEO.

It is maybe possible to upgrade the internal Proxmark3 (ARM, FPGA) in PC-Mode via the exposed com port as usual.

Beware proxmark3 client, firmware and FPGA image are all specific versions, don't use RRG/Iceman on them.

non PC-Mode

usb 1-2.3: New USB device found, idVendor=0525, idProduct=a4a5, bcdDevice= 4.14
usb 1-2.3: New USB device strings: Mfr=3, Product=4, SerialNumber=0
usb 1-2.3: Product: Mass Storage Gadget
usb 1-2.3: Manufacturer: Linux 4.14.111 with musb-hdrc
usb-storage 1-2.3:1.0: USB Mass Storage device detected
usb-storage 1-2.3:1.0: Quirks match for vid 0525 pid a4a5: 10000
scsi host2: usb-storage 1-2.3:1.0
usbcore: registered new interface driver usb-storage
usbcore: registered new interface driver uas
scsi 2:0:0:0: Direct-Access     Linux    File-Stor Gadget 0414 PQ: 0 ANSI: 2
scsi 2:0:0:0: Attached scsi generic sg0 type 0
sd 2:0:0:0: Power-on or device reset occurred
sd 2:0:0:0: [sda] 81920 512-byte logical blocks: (41.9 MB/40.0 MiB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 0f 00 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda:
sd 2:0:0:0: [sda] Attached SCSI disk
usb 1-2.3: USB disconnect, device number 36
sd 2:0:0:0: [sda] Synchronizing SCSI cache
sd 2:0:0:0: [sda] Synchronize Cache(10) failed: Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
usb 1-2.3: new high-speed USB device number 37 using xhci_hcd
usb 1-2.3: New USB device found, idVendor=0525, idProduct=a4a7, bcdDevice= 4.14
usb 1-2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-2.3: Product: Gadget Serial v2.4
usb 1-2.3: Manufacturer: Linux 4.14.111 with musb-hdrc
cdc_acm 1-2.3:2.0: ttyACM0: USB ACM device

So it appears briefly as Mass Storage under VID/PID 0525:a4a5 then as UART bridge under VID/PID 0525:a4a7

Interface

On some screens, e.g. when reading a tag, Proxmark3 console output can be displayed by pressing Right button. Font size can be modified by pressing the 2 top unlabeled buttons.

PC-Mode

usb 1-2.3: New USB device found, idVendor=1d6b, idProduct=0106, bcdDevice= 4.14
usb 1-2.3: New USB device strings: Mfr=3, Product=4, SerialNumber=0
usb 1-2.3: Product: Composite Gadget (ACM + MS)
usb 1-2.3: Manufacturer: Linux 4.14.111 with musb-hdrc
cdc_acm 1-2.3:1.0: ttyACM0: USB ACM device
usb-storage 1-2.3:1.2: USB Mass Storage device detected
scsi host2: usb-storage 1-2.3:1.2
scsi 2:0:0:0: Direct-Access     Linux    File-Stor Gadget 0414 PQ: 0 ANSI: 2
sd 2:0:0:0: Attached scsi generic sg0 type 0
sd 2:0:0:0: Power-on or device reset occurred
sd 2:0:0:0: [sda] 23146496 512-byte logical blocks: (11.9 GB/11.0 GiB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 0f 00 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda:
sd 2:0:0:0: [sda] Attached SCSI removable disk

Mass Storage makes ICOPY-X partition visible.

/dev/ttyACM0 allows to communicate directly with the Proxmark3. It is twice slower than a regular Proxmark3. It goes via a socat bridge in the NanoPi NEO:

/bin/sh -c sudo socat /dev/ttyGS0,raw,echo=0 /dev/ttyACM0,raw,echo=0

It is not identified as a Proxmark3 so if you're using another client than their official one, you can't use the pm3 script but you have to tell explicitly your client to use the right port, cf Compiling our client section.

UART1

Connect

On NanoPi NEO pins rx1 and tx1 (UART1 3v3) at 115200 bauds, the Debug console is available (pi/pi, fa/fa and root/fa, sudo is also available)

Internally, it corresponds to /dev/ttyS1

Boot & Shutdown

cf boot.log and shutdown.log

cat /proc/cmdline 
console=ttyS1,115200 earlyprintk root=/dev/mmcblk0p2 rootfstype=ext4 rw rootwait fsck.repair=yes panic=10 fbcon=map:0  data=/dev/mmcblk0p3 snd-soc-core.pmdown_time=3600000

Mount

physical partitions:

/dev/mmcblk0p1 on /boot type vfat (rw,relatime,fmask=0022,dmask=0022,codepage=437,iocharset=ascii,shortname=mixed,utf8,errors=remount-ro)
overlay on / type overlay (rw,relatime,lowerdir=/root,upperdir=/data/root,workdir=/data/work)
/dev/mmcblk0p4 on /mnt/upan type vfat (rw,relatime,fmask=0022,dmask=0022,codepage=437,iocharset=ascii,shortname=mixed,utf8,errors=remount-ro)

Processes

/usr/bin/sudo /usr/bin/xinit /etc/icopy.d/ipk_starter.py
/bin/sh -c sudo /home/pi/ipk_app_main/app.py
/bin/sh -c sudo -s /home/pi/ipk_app_main/pm3/proxmark3 /dev/ttyACM0 -w --flush

Explore app.py

$ python3 -i
>>> import sys, inspect
>>> sys.path.append("main")
>>> sys.path.append("lib")

>>> from lib import version
>>> version.SERIAL_NUMBER
'12345678'
>>> version.getSN()
'12345678'
>>> version.UID
... Some 78 base64-encoded bytes

>>> from lib import commons
>>> commons.getFlashID()
****************************************************************
开始执行命令 b'Nikola.D.CMD = mem info\r\n'
命令发送成功，开始进入接收
检测到通信结束协议字符，通信完成: 

[=] --- Flash memory Information ---------
... Dump of the "mem info" command execution on Proxmark3

命令执行时间(ms):  97.3889729976654
执行命令完成
****************************************************************
'0102030405060708'

>>> commons.startPlatformCMD('ls')
app.py main nikola res lib pm3

>>> from lib import games
>>> str(inspect.signature(games.GreedySnake))
"(canvas, block_size=10, default_len=3, default_xy=(28, 129), default_border=(4, 40, 240, 240), default_direction='UP')"

Install packages

apt-cache show strace | egrep '(Depends|Filename)'
Depends: libc6 (>= 2.15)
Filename: pool/main/s/strace/strace_4.11-1ubuntu3_armhf.deb
# Now from host:
# wget http://ports.ubuntu.com/pool/main/s/strace/strace_4.11-1ubuntu3_armhf.deb
# => ICOPY-X
sudo dpkg -i /mnt/upan/packages/strace_4.11-1ubuntu3_armhf.deb

Trace proxmark3 calls

First install strace as seen above

strace -p$(pgrep proxmark3) -s9999 -e write|sed -u 's/^[^"]*"//;s/"[^"]*$//;s/\\n$//;s/\\n/\n/g;s/\\t/\t/g;s/\\r/\r/g'
strace: Process 1234 attached

Now whenever app.py executes commands with the proxmark3 client, we'll see them as if it was our client.

[usb|script] pm3 --> hf 14a info

Nikola.D: 0
[usb|script] pm3 --> lf sea

[=] NOTE: some demods output possible binary
[=] if it finds something that looks like a tag
[=] False Positives ARE possible
[=] 
[=] Checking for known tags...
[=] 
[+] Indala - len 64, Raw: a0000000a0002021
[+] Fmt 26 FC: 1 Card: 2 checksum: 01
[+] Possible de-scramble patterns
[+]     Printed     | __0000__ [0x0]
[+]     Internal ID | 536879137
[+]     Heden-2L    | 320

[+] Valid Indala ID found!

Couldn't identify a chipset

Nikola.D: 0

Diagnosis:

hf tune
lf tune
lf sea
mem spiffs load f /tmp/test_pm3_mem.nikola o test_pm3_mem.nikola
mem spiffs wipe

STM32 commands over UART0

See STM32 Commands

Networking

We can add some network to the iCopy-X, see Networking

Rotated screen

During operations it happened to us that the screen got rotated.

The situation occurs when the NanoPi reboots without coordination with the STM32. E.g. a simple sudo shutdown -r now triggers it.

To fix it, power off the device and unplug external USB-C power supply.