-
Notifications
You must be signed in to change notification settings - Fork 23
New issue
Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.
By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.
Already on GitHub? Sign in to your account
Doesn't boot on OrangePi Zero 2 #32
Comments
RPI3 is too weak.
OPIZ2, may be an issue with the SD card. Currently Remote SDR version 5
image is running correctly on OPIZ2. I have good return I have one running
just in front of me.
73
F1ATB
Le mar. 21 mars 2023 à 15:49, osscombat ***@***.***> a écrit :
… Hi,
Just gave it a try on a new OPiZ2 recently - it doesn't work as expected.
No IP-address is being requested, no signal over mHDMI, network LEDs are
blinking though.
Note: RPI4 image boots fine even on RPi3, but probably this board is too
weak, the sound is jerking badly in the browser.
—
Reply to this email directly, view it on GitHub
<#32>, or unsubscribe
<https://github.com/notifications/unsubscribe-auth/ACN7K5OD7T3JBONW5DKBQZLW5G5WLANCNFSM6AAAAAAWCRUPCY>
.
You are receiving this because you are subscribed to this thread.Message
ID: ***@***.***>
--
André Buhart
F1ATB
https://f1atb.fr
https://sea-seek.com
|
It's not the sdcard, I have tried two different. Official 3.0.6 debian
image boots fine, will try the manual install.
вт, 21 мар. 2023 г., 19:27 F1ATB ***@***.***>:
… RPI3 is too weak.
OPIZ2, may be an issue with the SD card. Currently Remote SDR version 5
image is running correctly on OPIZ2. I have good return I have one running
just in front of me.
73
F1ATB
Le mar. 21 mars 2023 à 15:49, osscombat ***@***.***> a écrit :
> Hi,
> Just gave it a try on a new OPiZ2 recently - it doesn't work as expected.
> No IP-address is being requested, no signal over mHDMI, network LEDs are
> blinking though.
>
> Note: RPI4 image boots fine even on RPi3, but probably this board is too
> weak, the sound is jerking badly in the browser.
>
> —
> Reply to this email directly, view it on GitHub
> <#32>, or unsubscribe
> <
https://github.com/notifications/unsubscribe-auth/ACN7K5OD7T3JBONW5DKBQZLW5G5WLANCNFSM6AAAAAAWCRUPCY
>
> .
> You are receiving this because you are subscribed to this thread.Message
> ID: ***@***.***>
>
--
André Buhart
F1ATB
https://f1atb.fr
https://sea-seek.com
—
Reply to this email directly, view it on GitHub
<#32 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AHJ2YGOE72SNIYQCZ7U4K6LW5HJFTANCNFSM6AAAAAAWCRUPCY>
.
You are receiving this because you authored the thread.Message ID:
***@***.***>
|
I encountered the same problem: partial boot with the armbian logo on the hdmi output then nothing but the fixed cursor. |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
Hi,
Just gave it a try on a new OPiZ2 recently - it doesn't work as expected. No IP-address is being requested, no signal over mHDMI, network LEDs are blinking though.
Note: RPI4 image boots fine even on RPi3, but probably this board is too weak, the sound is jerking badly in the browser.
The text was updated successfully, but these errors were encountered: