This is an Arduino Library to produce square-wave of the specified frequency (and 50% duty cycle) on any Arduino pin.
A duration can optionally be specified, otherwise the wave continues until stop() is called.
The pin can be connected to a piezo buzzer or other speaker to play tones.
Be sure to try out the RTTTL (RingTone Text Transfer Language) example!
A simplified version of the Tone library has been incorporated into the Arduino core since 0018. It only provides a single tone (since only one timer is used). You can find the core documentation here.
Check out the tutorial by Tom Igoe at NYU's Interactive Telecommunications Program (ITP). It demonstrates how to use the core tone() and noTone() commands.
Do not connect the pin directly to some sort of audio input. The voltage is considerably higher than a standard line level voltages, and can damage sound card inputs, etc. You could use a voltage divider to bring the voltage down, but you have been warned.
You MUST have a resistor in line with the speaker, or you WILL damage your controller.
Unzip the folder and rename it to Tone, then move it to your arduinosketchfolder/libraries/ folder.
- Just connect the digital pin to a speaker (with a resistor - say 1K - in line), and the other side of the speaker to ground (GND).
|
 |
-
You can use a potentiometer to control the volume. Use a 10K Ohm potentiometer (variable resistor) in line with the 1K Ohm resistor connected to the speaker.
-
Using this library will affect usage of the PWM outputs, so be aware.
-
Also, although it's the last timer to be allocated, timer 0 (which is used for
millis()among other things) will be affected if used.
Tone tone1;
void setup(void)
{
tone1.begin(13);
}
- No properties.
begin(pin)- prepares a pin for playing a tone.isPlaying()- returnstrueif tone is playing,falseif not.play(frequency[,duration])- play a tone.frequencyis in Hertz, and thedurationis in milliseconds.durationis optional. Ifdurationis not given, tone will play continuously untilstop()is called.play()is non-blocking. Once called,play()will return immediately. Ifdurationis given, the tone will play for that amount of time, and then stop automatically.
stop()- stop playing a tone.
Below is a list of constant values of frequencies for notes. (These are included in the library).
e.g.
tone1.play(NOTE_B3);
| Constant Name | Frequency (Hz) |
|---|---|
| NOTE_B0 | 31 |
| NOTE_C1 | 33 |
| NOTE_CS1 | 35 |
| NOTE_D1 | 37 |
| NOTE_DS1 | 39 |
| NOTE_E1 | 41 |
| NOTE_F1 | 44 |
| NOTE_FS1 | 46 |
| NOTE_G1 | 49 |
| NOTE_GS1 | 52 |
| NOTE_A1 | 55 |
| NOTE_AS1 | 58 |
| NOTE_B1 | 62 |
| NOTE_C2 | 65 |
| NOTE_CS2 | 69 |
| NOTE_D2 | 73 |
| NOTE_DS2 | 78 |
| NOTE_E2 | 82 |
| NOTE_F2 | 87 |
| NOTE_FS2 | 93 |
| NOTE_G2 | 98 |
| NOTE_GS2 | 104 |
| NOTE_A2 | 110 |
| NOTE_AS2 | 117 |
| NOTE_B2 | 123 |
| NOTE_C3 | 131 |
| NOTE_CS3 | 139 |
| NOTE_D3 | 147 |
| NOTE_DS3 | 156 |
| NOTE_E3 | 165 |
| NOTE_F3 | 175 |
| NOTE_FS3 | 185 |
| NOTE_G3 | 196 |
| NOTE_GS3 | 208 |
| NOTE_A3 | 220 |
| NOTE_AS3 | 233 |
| NOTE_B3 | 247 |
| NOTE_C4 | 262 |
| NOTE_CS4 | 277 |
| NOTE_D4 | 294 |
| NOTE_DS4 | 311 |
| NOTE_E4 | 330 |
| NOTE_F4 | 349 |
| NOTE_FS4 | 370 |
| NOTE_G4 | 392 |
| NOTE_GS4 | 415 |
| NOTE_A4 | 440 |
| NOTE_AS4 | 466 |
| NOTE_B4 | 494 |
| NOTE_C5 | 523 |
| NOTE_CS5 | 554 |
| NOTE_D5 | 587 |
| NOTE_DS5 | 622 |
| NOTE_E5 | 659 |
| NOTE_F5 | 698 |
| NOTE_FS5 | 740 |
| NOTE_G5 | 784 |
| NOTE_GS5 | 831 |
| NOTE_A5 | 880 |
| NOTE_AS5 | 932 |
| NOTE_B5 | 988 |
| NOTE_C6 | 1047 |
| NOTE_CS6 | 1109 |
| NOTE_D6 | 1175 |
| NOTE_DS6 | 1245 |
| NOTE_E6 | 1319 |
| NOTE_F6 | 1397 |
| NOTE_FS6 | 1480 |
| NOTE_G6 | 1568 |
| NOTE_GS6 | 1661 |
| NOTE_A6 | 1760 |
| NOTE_AS6 | 1865 |
| NOTE_B6 | 1976 |
| NOTE_C7 | 2093 |
| NOTE_CS7 | 2217 |
| NOTE_D7 | 2349 |
| NOTE_DS7 | 2489 |
| NOTE_E7 | 2637 |
| NOTE_F7 | 2794 |
| NOTE_FS7 | 2960 |
| NOTE_G7 | 3136 |
| NOTE_GS7 | 3322 |
| NOTE_A7 | 3520 |
| NOTE_AS7 | 3729 |
| NOTE_B7 | 3951 |
| NOTE_C8 | 4186 |
| NOTE_CS8 | 4435 |
| NOTE_D8 | 4699 |
| NOTE_DS8 | 4978 |
Play a 440 Hz - musical note of 4^th^ octave A - on pin 13:
#include <Tone.h>
Tone tone1;
void setup()
{
tone1.begin(13);
tone1.play(NOTE_A4);
}
void loop()
{
}
The library uses the hardware timers on the microcontroller to generate square-wave tones in the audible range.
You can output the tones on any pin (arbitrary). The number of tones that can be played simultaneously depends on the number of hardware timers (with CTC capability) available on the microcontroller.
- ATmega8: 2 (timers 2, and 1)
- ATmega168/328: 3 (timers 2, 1, and 0)
- ATmega1280: 6 (timers 2, 3, 4, 5, 1, 0)
The timer order given above is the order in which the timers are allocated. Timer 0 is a sensitive timer on the Arduino since it provides millis() and PWM functionality.
The range of frequencies that can be produced depends on the microcontroller clock frequency and the timer which is being used:
| MCU clock | 8 bit timer Flow | 16 bit timer Flow | Fhigh |
|---|---|---|---|
| 8 MHz | 16 Hz | 1 Hz (1/16 Hz) | 4 MHz |
| 16 MHz | 31 Hz | 1 Hz (1/8 Hz) | 8 MHz |
Although Fhigh can go as high as 8 MHz, the human hearing range is typically as high as 20 kHz.
Tone accuracy is dependent on the timer prescalar. Frequency quantization occurs as the frequencies increase per prescalar.
If you used a 16 bit timer (e.g. timer 1, or timers 3,4,5 on '1280), you could generate "tones" down to 1/8 Hz (one cycle every 8 seconds), although the library only accepts integers for frequency.
After all is said and done, because play() only accepts unsigned integers for frequency, the maximum frequency that can be produced is 65535 Hz - which, after rounding, results in a 65573.77 Hz "tone" on a 16 MHz part. Even if play accepted larger values for frequency, you couldn't achieve better than around 80KHz with the Tone library because the pin toggling is done in software. Each toggle, in software, requires AT LEAST 50+ cycles.
