Skip to content

RPi program to use Bluetooth and/or USB gamepads and mice on retro 8/16-bit computers (C64, Amiga, etc)

License

Notifications You must be signed in to change notification settings

electronoora/joyemu

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

1 Commit
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

joyemu

This is a quick hack for enabling the use of either wireless Bluetooth and/or wired USB gamepads and mice on retro 8-bit and 16-bit computers such as Commodore Amiga and C64.

It works by reading events from HID input devices and emulating the pins of DB9 joysticks and a mouse on a Raspberry Pi and sending the signals via a 16-channel I/O board using the MCP23017 expander connected via I2C.

I've tested this code with two PS3 Sixaxis controllers (both in wired USB and Bluetooth mode) and an XBOX 360 wireless controller (via the USB adapter). The mouse support has been tested with a Microsoft 3600 Bluetooth Mouse and a wired SteelSeries Sensei Raw.

Any USB and Bluetooth HID devices are supported, as long as they present a Linux event device that can be accessed as /dev/input/event[0-9]+.

A more in-depth article on the project including some photos of the hardware can be found here:

https://haxor.fi/using-wireless-bluetooth-gamepads-and-mice-on-an-amiga-or-c64/

Compiling

For Raspbian users, install packages libevdev-dev and libi2c-dev to compile with the provided Makefile using GNU Make.

Usage

Usage: ./joyemu [-vqh] [-i bus] [-a addr] [-d (j1|j2|m):evdev] [-m port] [-j port] [-e type]

  -v		add verbosity
  -q		add quietness
  -i n		set I2C bus number for I/O expander (default: 1)
  -a 0xnn	set I2C address for I/O expander as a hexadecimal byte (default: 0x20)
  -d j1:n	set event device number for joystick 1
  -d j2:n	set event device number for joystick 2
  -d m:n	set event device number for mouse
  -m n		set mouse port: 1 (default) or 2
  -j n		set first joystick port: 1 or 2 (default)
  -e n		set mouse emulation type: 0=Amiga (default), 1=Atari ST
  -h		display this help

Note that if you log very verbosely to the console, the response to the inputs - especially that of the mouse - may begin to lag noticeably. Only use the more verbose debugging levels for actual debugging.

Hardware

I'm developing this on a Raspberry Pi Zero W and an IO Pi Zero expander board from AB Electronics. The reason I'm using a separate I/O expander is that the Atari-style DB9 joystick ports are active-low, so the pins on the computer end have pull-up resistors to +5V. On a Commodore C64 the pull-ups are internal to the CIA chips, whereas on an Amiga A500 or A1200 use external 4.7Ω resistors. The GPIO pins on the Raspberry Pi are not safe for +5V so they cannot be used unless external level conversion is used.

Any other I/O board (or built-in GPIOs with level conversion) would probably work equally well, as long as it sends 0V..+5V and tolerates the +5V pull-ups. Of course, you'd also have to rewrite io.c and io.h accordingly to support the hardware.

GPIO lines on the MCP23017 are connected to DB9 pins as follows:

Connector up down left right fire1 fire2
DB9 1/2 1 2 3 4 6 9
GPIOA/GPIOB 0 1 2 3 4 5

Bits 6 and 7 on GPIOA and GPIOB are unused.

I've added a 2x8 pin header on the I/O board and built a cable that connects the corresponding GPIO pins to two female DB9 connectors. Remember to also connect the ground plane on the I/O board with the ground pin on the DB9 connectors (pin 8).

License

Copyright (c) 2017 Noora Halme

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

  1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

  2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

About

RPi program to use Bluetooth and/or USB gamepads and mice on retro 8/16-bit computers (C64, Amiga, etc)

Topics

Resources

License

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published