Skip to content

pdaxrom/microcpu

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

(c) sashz sashz@pdaXrom.org, 2020-2021

GitHub project page

MICROCPU - 16-bit RISC CPU (Version 2)

Registers

The processor has eight 16-bit registers. The register 0 (PC) using as program counter.

Numeric Name Alias
0 R0 PC
1 R1 SP
2 R2 LR
3 R3 V0
4 R4 V1
5 R5 V2
6 R6 V3
7 R7 V4

Each register has high byte and low byte:

15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
HIGH BYTE LOW BYTE

Top

Address modes

The processor has 5 addressing modes that can be used by the programmer:

  1. Register
  2. Immediate
  3. Immediate indexed
  4. Register indexed
  5. Relative

Top

Instructions

Machine instructions generally fall into three categories: data movement, arithmetic/logic, control-flow and cpu modes control. We use the following notation:

Notation Description
<dst> Any destination register
<src> Any source register
<imm> 8-bit immediate
<imm16> 16-bit immediate
<idx> Any register or 4-bit unsigned immediate
<arg1> Any register
<arg2> Any register or 4-bit unsigned immediate
<rel> 11-bit signed immediate

Top

Data Movement Instructions

Instruction Description
LDRL <dst>, <src>, <idx> RL<dst> = M[R<src> + idx] Load low byte from source address + index
STRL <dst>, <src>, <idx> M[R<src> + idx] = RL<dst> Store low byte to source address + index
LDR <dst>, <src>, <idx> R<dst> = M[R<src> + idx] Load register (2 bytes) from source address + index
STR <dst>, <src>, <idx> M[R<src> + idx] = R<dst> Store register (2 bytes) to source address + index
SETL <dst>, <imm> RL<dst> = imm Copy low byte from constant
SETH <dst>, <imm> RH<dst> = imm Copy high byte from constant
MOVL <dst>, <src> RL<dst> = RL<src> Copy source low byte to destination low byte
MOVH <dst>, <src> RH<dst> = RL<src> Copy source low byte to destination high byte
MOV <dst>, <src> R<dst> = R<src> Copy data from source to destination register

Little endian byte order using for LDR and STR.

Examples:

    SETL V0, 0
    SETH V0, $10
    LDRL V1, V0, 0
    SETL V2, 1
    SETH V2, 0
    STR  V1, V0, V2
    MOV V3, V2

Top

Arithmetic and Logic Instructions

Instruction Description
ADD <dst>, <arg1>, <arg2> <dst> = <arg1> + <arg2> Add
SUB <dst>, <arg1>, <arg2> <dst> = <arg1> - <arg2> Subtract
SHL <dst>, <arg1>, <arg2> <dst> = <arg1> << <arg2> Logic shift left
SHR <dst>, <arg1>, <arg2> <dst> = <arg1> >> <arg2> Logic shift right
AND <dst>, <arg1>, <arg2> <dst> = <arg1> & <arg2> And
OR <dst>, <arg1>, <arg2> <dst> = <arg1> | <arg2> Or
INV <dst>, <arg1> <dst> = ~<arg1> Inversion
XOR <dst>, <arg1>, <arg2> <dst> = <arg1> ^ <arg2> Exclusive Or
SXT <dst>, <arg1> <dst> = sign <arg1> Sign extend

Examples:

    ADD V0, V1, V2
    SUB V0, V2, V1
    SHR V0, V0, 1
    SXT V1, V1

Top

Control Flow Instructions

Instruction Description
B <rel> PC = PC + <rel> Branch
EQ <arg1>,<arg2> PC = PC + (<arg1> == <arg2>) ? 2 : 0 Skip next command if arg1 and arg2 are equal
NE <arg1>,<arg2> PC = PC + (<arg1> != <arg2>) ? 2 : 0 Skip next command if arg1 and arg2 are not equal
LT <arg1>,<arg2> PC = PC + (<arg1> < <arg2>) ? 2 : 0 Skip next command if arg1 is less than arg2 (signed)
GE <arg1>,<arg2> PC = PC + (<arg1> >= <arg2>) ? 2 : 0 Skip next command if arg1 is greater then arg2 or equal (signed)
LTU <arg1>,<arg2> PC = PC + (<arg1> < <arg2>) ? 2 : 0 Skip next command if arg1 is less than arg2 (unsigned)
GEU <arg1>,<arg2> PC = PC + (<arg1> >= <arg2>) ? 2 : 0 Skip next command if arg1 is greater then arg2 or equal (unsigned)
BTC <arg1>,<arg2> PC = PC + (<arg1> & <arg2>) ? 2 : 0 Skip next command if arg1 AND arg2 result is zero
BTS <arg1>,<arg2> PC = PC + (<arg1> & <arg2>) ? 2 : 0 Skip next command if arg1 AND arg2 result is not zero

Examples:

    B	start
    EQ	V0, V1
    B	not_the_same
    B	the same

Top

CPU Modes Control

Instruction Description
SWS UPC = PC; PC = VEC_SUPER Switch to superuser mode
SWU PC = UPC Return to user mode
GETS <dst> <dst> = <User PC> Get user programm counter
SETS <src> <User PC> = <src> Set user programm counter

Examples:

    ORG	$0
    B	start
    B	su
    ...
su  SUB SP, SP, 2
    PUSH V0
    GETS V0
    ...
    PUTS V0
    POP  V0
    ADD SP, SP, 2
    SWU
    ...
ini SWS
    ...

Top

Interrupts

The system supports two interrupts - the CPU command to switch to superuser mode (SWS command) and peripheral interrupt (external signal). Both interrupts cause a jump to address $0002 while saving the interrupted address in a special register, which is available for modification using the GETS and PUTS commands. Exit from the interrupt mode is performed using the SWU command. Until the end of the execution of the mode, other interrupts are prohibited.

Top

MicroAssembler

Assembler has support for macros, procedures. Since the processor has a limited number of instructions, some instructions can be implemented as macros.

Top

Assembler directives

Directive Description
<symbol> EQU <exp> Set a symbol equal to an expression
DB <imm>[,<imm>...] Define constant byte(s)
DW <imm16>[,<imm16>...] Define constant word(s)
DS <imm16>[,<imm>] Reserves num bytes of space and initializes them to val (optional, defaul 0).
ALIGN <imm> Align address to num bits
ORG <imm16> Set location address counter
INCLUDE <file name> Include external source file
CHKSUM Insert constant word to binary to sum all words as $FFFF

Examples:

    INCLUDE functions.inc
CONST_ONE EQU 1
CONST_TWO EQU 2
    ORG $100
    DB 1, $2, $3, 4, 5
    DB "Hello, World", 0
    DB 'About'
    DW $1234, 8192, 0
    DS 32
    DS 64,$FF
    ALIGN 4

Top

Accembler macro definition

Directive Description
MACRO <name> Start macro
ENDM End macro

macro parameters start with # and are numbered from 1.

Example:

    MACRO SET
    SETH	#1, /#2
    SETL	#1, #2
    ENDM

    SET V0, $1234

Top

Assembler procedures

Directive Description
<label> PROC Start procedure
GLOBAL <label>[,<label>...] Add local procedure label as global
ENDP End procedure

Example:

get_one PROC
    SET V0, 1
    ADD PC, LR, 3
    ENDP
	
get_1 PROC
    GLOBAL get_2
    SET V0, 1
return ADD PC, LR, 3
get_2 SET V0, 2
    B return
    ENDP

Top

Command line options

microasm [-verilog|-binary] <input.asm> [output]

  • -verilog - create verilog ram file
  • -binary - create binary file

By default, the output file is hex file.

Top

Bootloader

The bootloader is using to load code and data into RAM, save memory from RAM and run the code .

Top

Bootloader options

  • bootloader <uart port> load <file.bin> [<start address> [<end address>]]
  • bootloader <uart port> save <file.bin> <start address> <end address>
  • bootloader <uart port> go [<address>]

load - load a binary file to RAM

save - save RAM to a binary file

go - execute code

Top

Lattice Diamond programmer and ftdi jtag dual channel board

To work correctly with ftdi jtag, remove the ftdi_sio module:

sudo rmmod ftdi_sio

Open the Programmer, reconnect the FTDI board and disconnect the JTAG port:

./ft2232d-util/ft2232d-ctl

Top