Releases: VoronDesign/Voron-Trident
Voron Trident r1
This release contains QoL updates and improvements to the official release of the VORON Trident 3d printer.
For more detailed information about Voron Trident itself, please refer to the official release notes and the previous update Trident
If you're just getting started with your Trident build, the files attached to this release contain the most up-to-date parts required for your Voron 3D printer. If you are currently building, or have already built your Trident, please check the list of fixes and updates below and determine whether you need to update your printer accordingly.
The following fixes and updates have been made since the previous release:
- Revised front idlers with tensioning screws moved to be inline with the idler pulleys. Inspiration for this modification taken from V2.4 Github issue - posted by chrisingham05
- Updated z_bed_*.stl files to increase max Z travel by 3mm.
- All unsupported countersunk bolt holes changed to using the cross-bridge method instead of a chamfer. (AB Stepper mounts, XY Joints and Panel Clips included in this update)
- Updated skirt fan mounts using M3 screws and heatsets to mount the fans and fan blanks. Inspiration for the heatset mounting method taken from Ali Express vendor.
- Updated Afterburner related files correcting issues with heatset insert hole sizes
- Added mounts for using Wago connectors for the mains and bed wiring.
- Added an exhaust filter fan grill to correct spacing for the fan mounting screws
- Included zip tie anchors for when using 3 hole style cable chains without integrated wire anchor tabs.
- Updated XY endstop pod compatible with both independent and PCB mounted D2F microswitches.
- Fixed issue #57 (Spider v2.2 controller mounts interfering with underboard fuse)
- Fixed issue #62 (heatset insert location on front skirt)
- Updated assembly manual.
Special thanks to all the contributors
Thank you to everyone who contributed to this update and reported issues with the original release.
Voron Trident
Release Notes
This marks the full release of the Voron Trident 3D printer.
If you're just getting started with your Voron Trident build, the files attached to this release contain the most up-to-date parts required for your Voron 3D printer build. If you are currently building, or have already built your Voron Trident, please check the list of fixes and updates below and determine whether you need to update your printer accordingly.
Since the pre-release, the following changes have been made:
- 8326994: Fixed CAD filename
- 0df5d06, 4369164: Manual Updates and Fixes
- 5cfb431: Updates hex nut positions to improve M5 thread engagement on z-carriages
- ab21663: Fix mini12854 display knob for better engagement when pressed
- 3ac73d4, a258ac6: Update CAD to reflect changes of other commits
- 017df26, f8f42b7: Fix Z-tilt coordinates in sample config
- bf77e86: Updated blower housing for AB, improving wiring clearance, add panasonic probe holder
- f669998: Remove redundant sections from sample config
Voron Trident Pre-Release Notes
Welcome Voron Trident, the evolution of the Voron 1 platform. While nearly every component has changed, an easy upgrade path was retained for current Voron 1.8 owners. The files attached to this release are the most up-to-date parts required to build your Voron 3D printer. Please see the list below for changes from Voron 1.8.
- Gantry
- AB Stepper Mounts
- Revised geometry to help prevent improper belt routing.
- New wiring path with cover that does not capture the gantry wiring harness.
- Optional A stepper mounted Y endstop switch.
- XY Axis
- Adopted the Voron 2.4 XY Axis layout with bottom mounted linear rails. This includes the ability to utilize the V2.4 style endstop pod (microswitch or hall effect)
- Integrated the community developed MGN12 X axis setup.
- Updated cable chain routing to match the V2.4 setup
- AB Stepper Mounts
- Z Axis
- Completely new three stepper configuration.
- Utilizes MGN9H linear rails instead of linear rods.
- Utilizes GE5C spherical bearings at each joint
- Integrated Cable chain wire management
- Uses the V2.4 Z endstop switch assembly
- Retains compatibility with the V1.8 build plate
- Increased max Z travel to 250mm
- Completely new three stepper configuration.
- Skirts and Electronics Compartment:
- Reconfigured all electronics to be located below the deck.
- Shares dimensions and screen and side fan compatibility with Voron 2.4
- New power supply and electronic mounts
- New front Mini12864 display mount.
- New recommended feet but retains compatibility with the compressor feet.
- Panels and Exhaust:
- Slightly modified exhaust housing utilizing two screws to better hold the filter cover.
- Updated panel clips to support the recommended use of 3mm foam tape on the side panels and 1mm foam tape on the top and rear panels.
- Requires new panels for all but the top panel.
- Miscellaneous
- Added support for 350mm build plates
- V1.8 frame upgrade possible with minimal modifications. See frame upgrade manual.
Special thanks to all the contributors
Thank you to everyone who contributed to this update and reported issues with the pre-release.
More information
Voron Trident initial release
Note: This is the pre-release of Voron Trident. For the full release, which includes some minor fixes and updates, please go here!
Welcome Voron Trident, the evolution of the Voron 1 platform. While nearly every component has changed, an easy upgrade path was retained for current Voron 1.8 owners. The files attached to this release are the most up-to-date parts required to build your Voron 3D printer. Please see the list below for changes from Voron 1.8.
Release Notes:
- Gantry
- AB Stepper Mounts
- Revised geometry to help prevent improper belt routing.
- New wiring path with cover that does not capture the gantry wiring harness.
- Optional A stepper mounted Y endstop switch.
- XY Axis
- Adopted the Voron 2.4 XY Axis layout with bottom mounted linear rails. This includes the ability to utilize the V2.4 style endstop pod (microswitch or hall effect)
- Integrated the community developed MGN12 X axis setup.
- Updated cable chain routing to match the V2.4 setup
- AB Stepper Mounts
- Z Axis
- Completely new three stepper configuration.
- Utilizes MGN9H linear rails instead of linear rods.
- Utilizes GE5C spherical bearings at each joint
- Integrated Cable chain wire management
- Uses the V2.4 Z endstop switch assembly
- Retains compatibility with the V1.8 build plate
- Increased max Z travel to 250mm
- Completely new three stepper configuration.
- Skirts and Electronics Compartment:
- Reconfigured all electronics to be located below the deck.
- Shares dimensions and screen and side fan compatibility with Voron 2.4
- New power supply and electronic mounts
- New front Mini12864 display mount.
- New recommended feet but retains compatibility with the compressor feet.
- Panels and Exhaust:
- Slightly modified exhaust housing utilizing two screws to better hold the filter cover.
- Updated panel clips to support the recommended use of 3mm foam tape on the side panels and 1mm foam tape on the top and rear panels.
- Requires new panels for all but the top panel.
- Miscellaneous
- Added support for 350mm build plates
- V1.8 frame upgrade possible with minimal modifications. See frame upgrade manual.