Skip to content
New issue

Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.

By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.

Already on GitHub? Sign in to your account

Re-fix the STM32 dual-bank bootloader stuff. #9738

Merged
merged 2 commits into from
Jul 16, 2020
Merged
Changes from all commits
Commits
File filter

Filter by extension

Filter by extension

Conversations
Failed to load comments.
Loading
Jump to
Jump to file
Failed to load files.
Loading
Diff view
Diff view
46 changes: 15 additions & 31 deletions tmk_core/common/chibios/bootloader.c
Original file line number Diff line number Diff line change
Expand Up @@ -2,6 +2,7 @@

#include "ch.h"
#include "hal.h"
#include "wait.h"

/* This code should be checked whether it runs correctly on platforms */
#define SYMVAL(sym) (uint32_t)(((uint8_t *)&(sym)) - ((uint8_t *)0))
Expand Down Expand Up @@ -31,45 +32,28 @@

extern uint32_t __ram0_end__;

# define bootdelay(loopcount) \
do { \
for (int i = 0; i < loopcount; ++i) { \
__asm__ volatile("nop\n\t" \
"nop\n\t" \
"nop\n\t"); \
} \
} while (0)

void bootloader_jump(void) {
*MAGIC_ADDR = BOOTLOADER_MAGIC; // set magic flag => reset handler will jump into boot loader
NVIC_SystemReset();
}

void enter_bootloader_mode_if_requested(void) {
unsigned long *check = MAGIC_ADDR;
if (*check == BOOTLOADER_MAGIC) {
*check = 0;

// For STM32 MCUs with dual-bank flash, and we're incapable of jumping to the bootloader. The first valid flash
// bank is executed unconditionally after a reset, so it doesn't enter DFU unless BOOT0 is high. Instead, we do
// it with hardware...in this case, we pull a GPIO high/low depending on the configuration, connects 3.3V to
// BOOT0's RC charging circuit, lets it charge the capacitor, and issue a system reset. See the QMK discord
// #hardware channel pins for an example circuit.
palSetPadMode(PAL_PORT(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_PAD(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_MODE_OUTPUT_PUSHPULL);
// For STM32 MCUs with dual-bank flash, and we're incapable of jumping to the bootloader. The first valid flash
// bank is executed unconditionally after a reset, so it doesn't enter DFU unless BOOT0 is high. Instead, we do
// it with hardware...in this case, we pull a GPIO high/low depending on the configuration, connects 3.3V to
// BOOT0's RC charging circuit, lets it charge the capacitor, and issue a system reset. See the QMK discord
// #hardware channel pins for an example circuit.
palSetPadMode(PAL_PORT(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_PAD(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_MODE_OUTPUT_PUSHPULL);
# if STM32_BOOTLOADER_DUAL_BANK_POLARITY
palSetPad(PAL_PORT(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_PAD(STM32_BOOTLOADER_DUAL_BANK_GPIO));
palSetPad(PAL_PORT(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_PAD(STM32_BOOTLOADER_DUAL_BANK_GPIO));
# else
palClearPad(PAL_PORT(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_PAD(STM32_BOOTLOADER_DUAL_BANK_GPIO));
palClearPad(PAL_PORT(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_PAD(STM32_BOOTLOADER_DUAL_BANK_GPIO));
# endif

// Wait for a while for the capacitor to charge
bootdelay(STM32_BOOTLOADER_DUAL_BANK_DELAY);
// Wait for a while for the capacitor to charge
wait_ms(100);

// Issue a system reset to get the ROM bootloader to execute, with BOOT0 high
NVIC_SystemReset();
}
// Issue a system reset to get the ROM bootloader to execute, with BOOT0 high
NVIC_SystemReset();
}

void enter_bootloader_mode_if_requested(void) {} // not needed at all, but if anybody attempts to invoke it....

#elif defined(STM32_BOOTLOADER_ADDRESS) // STM32_BOOTLOADER_DUAL_BANK

extern uint32_t __ram0_end__;
Expand Down